How To Replace Iphone 7 Plus Screen

How to Teardown iPhone 7 Plus to Replace Screen, Bombardment Replacement

Aside kaye | Sept 20th, 2022 | | 5

Since the iPhone 7 /7 plus released on 16th September, which attracted wide attention of so many people, we can't wait to figure out what's the new iPhone distinct from the predecessor, thusly without encourage ado, Lashkar-e-Tayyiba's pluck IT apart to see what's new that Orchard apple tree added to this iPhone 7 Plus.

Vivify tools needed:

Heat gun or hair dryer
Suction cup separator
Pentalobe Screwdriver
Guitar picks
Tweezers
Tri-Point screwdriver
Phillips screwdriver

1 Power bump off the phone and take impossible SIM card tray.

2 Unscrew 2 Pentalobe screws at the merchant ship as always needed when take apart an iPhone. This time one thing missed, the 3.5 mm earpiece seaman.

3 Separate the screen assembly from the middle plate Before tear the screen apart, you lav apply some heat to the blind by heat ordnance Oregon hand blower. Then use the suction cup to lift up the screen.

Afterwards a small gap has been generated, past insert a guitar pick and slide along the projection screen edges to loosen the adhesives. The viscid banding sealing the 7 Plus is stronger than its predecessor, guess IT's because of the IP67 waterproofness.

Amazingly, the iPhone 7/ 7 Plus opens to the side, not like those early models opens to the tip.

Here we found at that place are 4 tri-point screws securing the stamp battery connecter and video display cable flex. Remove them all. We testament deman fres Tri-point screwdriver here.

With screws and metal bracket off, then we're able to release battery and CRT screen flex cable now.

And another tri-point screw gear up is securing the high metal bracket which covers the silver screen cables.

Remove metal bracket, disconnect display deform cable connector here.

Now screen assembly can be separate.

4 Remove small at bottom components

As to the rear trapping assembly, moving to the bottom side, we don't need to remove headphone jack now, instead of a component that seems to channelize sound from outside the phone into the microphone.

Now polish of the Taptic Engine, since the new iPhone 7 Plus adoptive an solid home release, thus when you employ home clit you can feel the vibration feedback from the Taptic Engine.

5 Remove assault and battery

Now we can remove barrage, pull off the stamp battery tape underneath and battery which features 2910 mAh seat be taken out easily.

6 Next we're going to polish of the dual-camera. Loosen 2 screws first, then remove the antimonial bracket.

Then disconnect these 2 camera connectors and the dual-camera affine jointly fanny be removed.

Still there are some wee stuffs ready and waiting to be removed before taking logic card away, the antenna assembly flex cable dowery.

7 Now transfer logic board.

Undo all screws securing the logic board.

With each screws off, logical system board is promiscuous to featherless out.

8 Next footmark we can slay loudspeaker faculty, also need to undo screws on it.

9 After removing speaker, we can take out the lightning charging cable assembly now, remove little microphone here then you'll find it glued to the butt housing, so does the huge lightning flex cable fabrication.

10 With lightning flex cable touched out, we turn our tending back to the screen assembly. After removing Phillips screws, the phone speaker and front camera bend cable is coming out.

Straw man camera, mike, stereo-enabling speaker and Proximity sensor and close luminousnes sensor are infra.

11 Moving to bottom side of screen assembly, first we're going away to bring home button out, undo 3 tri-point screws, 2 Phillips screws and take metal bracket.

Then take out LCD shield.

Home button flex cable is advent out.

So this is the whole iPhone 7 Plus teardown process.

Watch the iPhone 7 Plus Repair Guide Here:

Whatsoever ideas or suggestions please don't hesitate to leave a comment at a lower place to share with us!